A high level of skill and attention to detail is necessary for the carpentry profession, and a specific plan must take every action taken.
A significant amount of care must be made while utilizing the many tools and equipment available in this trade; each has a specific purpose.
Among these instruments is a table saw, which is essential and considered the foundation of carpentry. One of the most common questions asked by carpenters is why is table saws bind during cutting.
In woodworking projects, table saw binding can lead to catastrophic failures. Not only does it cut the woods wrong, but it is also very unsafe and may result in accidents and injuries.
Table saw a variety of factors that may cause binding, and since this is such an essential factor in carpentry, we will examine each of these factors in this article. We welcome you to participate in this article with us.
Table saw binding causes
The table saw has two blades, one on each side (front and back of the table saw), and if the dimensions of the back blade are less than the dimensions of the front blade, your table saw will close while you are cutting wood.
Your wood or board will go in a triangular pattern rather than straight lines when this occurs. The wood starts to squeeze during the cutting process, forcing the table saw to shut down completely.
Binding between the blades and the curve created by this motion induces a slight bend in the blade.
Consequently, the blade returns to its original position, generating an impact.
A low-quality, sluggish, and broken blade with many teeth sets missing can cause your table saw to bind. If this is the case, the remedy is to purchase a replacement blade of higher quality.
The best ways to correct table saw binding
A highly significant and hazardous problem in carpentry, binding can result in mishaps such as wood burning and catastrophic injuries.
When you’re standing behind a stick or with your head slightly above the piece of wood you’re cutting, avoid ripping the wood. Working away from the blade line is essential for your safety.
Do not be concerned about this issue since, as with all problems, a solution will eventually be found.
When it comes to binding, the approach you employ to remedy the issue will be determined by the source of the problem.
There are some common factors that cause table saw binding:
| Factors | Descriptions |
| Poor blade quality | In other circumstances, the quality of the blade could cause the binding issue; in these cases, the only way to repair the situation is to get a new and high-quality blade. Because of this, it is critical to inspect the quality and condition of your blade before making a purchase. |
| Number of Teeth in the Blade | The number of teeth on the blade is one of the most important things to consider while planning the cutting process. One could claim that having more teeth results in a quicker and smoother cutting operation. It should be emphasized that fewer teeth result in more wood being torn by the teeth. |
| Tooth Angle | The angle formed by the centerline of the blade is referred to as the blade angle. Positive and negative teeth are arranged at two distinct curves on the blade. It is possible to move the blade forward to a certain degree when the tooth angle is positive, as shown in the illustration. The negative angle of the tooth (or hook), on the other hand, indicates that the teeth of the blade have been slanted backward in the blade. A common rule of thumb is that the greater the positive angle at your blade’s teeth, the more aggressive the blade is. |
| Configuration of the teeth | When it comes to blade teeth, it’s important to remember that there are many sorts available, including Flat Top (FT), which is built for ripping, and Alternate Top Bevel (ATB), which is meant for cross-cutting. Consider the kind of cut and the project’s material while selecting the best one.
|
| Misalignment of the blade | The second issue that can be a binding factor cause is a poor blade or fence alignment, in which case you must adjust the saw so that the blade is parallel to the fence and vice versa. There should be a difference in size between the front and rear blades that is larger than or equal to the dimensions of the front blade. You may measure the distance between a specific tooth in the front and use that exact measurement (of the same tooth) to align the dimension of the tooth in the rear. If you cannot reset the size, we suggest that you consult the owner’s handbook for assistance. They have their instructions on aligning fences and saw blades on their machines. |
To Sum It Up
The subject of this article was Why is my table saw binding?
When operating a table saw, the essential thing to remember is to make sure the blade is in good condition and well-aligned. Invest in a high-quality blade that is appropriate for your kind of wood.
Make sure it’s securely fastened in place. Then, make sure that you’ve checked that your fence gaps are parallel to one another.
We hope that the information provided here has been helpful to you and that you can work out any issues about table saw binding you may be having so that you may continue to practice and perfect your carpentry skills.
Frequently asked questions about table saw binding.
-
What Is the Best Way to Tell if My Table Saw is Binding?
Burns on the wood are one of the earliest symptoms of table saw binding. Burns are generated by the binding caused by the uneven blade, which warms up the wood surfaces.
-
Do you know why my table saw cuts?
In rare cases, your table saw may malfunction owing to a faulty motor overload switch, worn motor brushes, or an excessive blade connection. Your traction wire may also have been improperly installed.
